MG Motherboard Manual ECS PCChips G 1 5E English. DownloadReport. Published on Oct View Download AddThis. The MG v motherboard and It’s latest BIOS is almost 5 years old so It should support hard go to pcchip web site download manual jim. DownloadPcchips mg motherboard manual pdf. Please note that tracking information might not be immediately available. She takes great joy in supporting .
|Published (Last):||4 November 2013|
|PDF File Size:||12.76 Mb|
|ePub File Size:||3.87 Mb|
|Price:||Free* [*Free Regsitration Required]|
This publication, n863g photographs, illustrations and software, is under the protection of international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without the express written consent of the manufacturer. The information in this document is subject to change without notice.
The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Further, the manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.
Other names used in this publication may be trademarks and are acknowledged. I Static Electricity Precautions Take the following precautions while unpacking this motherboard and installing it in a system.
While installing, please wear a grounded wrist strap maunal possible. Carefully hold this motherboard by its edges.
Do not touch those components unless it is absolutely necessary. Put this motherboard on the top of static-protection package mnaual component side facing up while installing. Inspect this motherboard whether there are any damages to components and connectors on the board. If you suspect this motherboard has been damaged, do not connect power to the system.
Contact your motherboard vendor about those damages. Therefore, it might happen under Windows XP that a dialogue box shown as below pop out warning you this software has not passed Windows Logo testing to verify its compatibility with Windows XP.
Please rest assured that our RD department has already tested and verified these drivers. As soon as the solution is done, the updated USB drive will be released to our website: Di questa scheda madre sono stati sviluppati due modelli: Key Features This motherboard has these key features: Hardware specifications and software items are subject to change without notification.
Package Contents Your motherboard package contains the following items: You can purchase your own optional accessories from the third party, but please contact your local vendor on majual issues of the specification and compatibility.
Before installing this manuxl, make sure jumper JP2 is under Normal setting. See this chapter k863g information about locating JP2 and the setting options. Never connect power to the system during installation; otherwise, it may damage the motherboard. Motherboard Components Identify major components on the motherboard via this diagram underneath. Use the Parallel port to connect printers or other parallel communications devices.
Audio Ports Use the three audio ports to connect audio devices. The first jack is for stereo Line-In signal.
The second jack is for stereo LineOut signal. The third jack is for Microphone. Installing the Processor This motherboard has a Socket processor socket. When choosing a processor, consider the performance requirements of the system. Performance is based on the processor design, the manusl speed and system bus frequency of the processor, and the quantity of internal cache memory and external cache memory.
PC CHIPS MG (VA) |
Unhook the locking lever of the CPU socket. Pull the k863g lever away from the socket and raising it to the upright position. Match the pin1 corner marked as the beveled edge on the CPU with the pin1 corner on the socket. Insert the CPU into the socket. Do not use force. Push the locking lever down and hook it under the latch on the edge of socket.
MG (VA) PCCHIPS PC-CHIPS Motherboard Mainboard Drivers Manuals BIOS
Apply thermal grease to the top of the CPU. Installing Memory Modules This motherboard accommodates two pin 2. Following these steps to install the memory module. Push down the latches on both sides of the DIMM socket. Align the memory module with the socket.
Manual for PC Chips M863g V 7.1 – PC Chips Computers & Internet
Install the DIMM module into the socket and press it firmly down until it is seated correctly. The socket latches are levered upwards and latch on to the edges of the DIMM. Install any remaining DIMM modules. You may need to clear the CMOS memory if the settings in the Setup Utility are incorrect that prevents your motherboard from operating.
The board is a Micro ATX size motherboard. You can install this motherboard in an ATX case. Install the motherboard in a case. J1 is the CPU Vcore power connector. If there is a cooling fan installed in the system chassis, connect the cable from the cooling fan to the SYSFAN1 fan power connector on the motherboard.
Front Panel Audio Connector This connector allows the user to install auxiliary front-oriented microphone and line-out ports for easier access. Additionally, some computer cases have USB ports at the front of the case. Locate the USB2 connector on the motherboard. Plug the bracket cable onto the USB2 connector. Remove a slot cover from one of the expansion slots on the system chassis. Install an extension bracket in the opening. Secure the extension bracket to the chassis with a screw.
You can use a card reader to read or transfer files and digital images to your computer. Please check the pin assignment of the cable and the USB header on the motherboard. Make sure the pin assignment will match before plugging manua. Any incorrect usage may cause unexpected damage m863h the system. Infrared Port The infrared port allows manuaal wireless exchange of information between your computer and similarly equipped devices such as printers, laptops, Personal Digital Assistants PDAsand other computers.
Locate the infrared port IR1 connector on the motherboard. If you are adding an infrared port, connect the ribbon cable from the port to the Manuql connector and then secure the port to an appropriate place in your system chassis. Drives can be 3. Install your drives and connect power from the system power m863f.
Use the cable provided to connect the drives to the floppy disk drive connector FDC1. If you connect two devices to a single cable, you must configure one of the drives maual Master and one of the drives as Slave.
The documentation of the IDE device will tell you how to configure the device as a Master or Slave device. The Master device connects to the end of the cable. Install the device s and connect power from the system power supply. If you have two devices on the cable, one must be Master and one must m863t Slave. On the motherboard, locate the 4-pin connector CD1. Remove the blanking plate of the slot from the system chassis.
Install the edge connector of the expansion card into the slot. Ensure the edge connector is correctly seated in the slot. Secure the metal bracket of the card to the system chassis with a screw.
Your computer applies those information to initialize all the components when booting up and basic functions of coordination between system components. If the Setup Utility configuration is incorrect, it may cause the system to malfunction. It can even stop your computer booting properly. If it happens, you can use the clear CMOS jumper to clear the Manal memory which has stored the configuration information; or you can hold down the Page Up key while rebooting your computer.
Holding down the Page Up key also clears the setup information.
58852588 M863G Motherboard Manual ECS PCChips 863G 1 5E English
You can run the setup utility and manually change the configuration. You might need to do this to configure some hardware installed in or connected to the motherboard, such as the CPU, system memory, disk drives, etc.
Whenever you see this message, press the Delete key, and the Main menu page of the Setup Utility appears on your manaul. You can use cursor arrow keys to highlight anyone of options on the main menu page.
Press Enter to select the highlighted option. Press the Escape key to leave the setup utility. Some options on the main menu page lead to tables of items with installed values that you can use cursor arrow manhal to highlight one item, and press PgUp and PgDn keys to cycle through alternative values of that item.
The other options on the main menu page lead to dialog boxes requiring your answer Yes or No by hitting the Y or N keys. If you have already changed the setup utility, press F10 to save those changes and exit the utility. Press F1 to display a screen describing all key functions. Press F9 to install the setup utility with a set of default values.
To configure an IDE hard disk drive, choose Auto.