ASTM C582 PDF

ASTM C + REDLINE: STANDARD SPECIFICATION FOR CONTACT- MOLDED REINFORCED THERMOSETTING PLASTIC (RTP) LAMINATES FOR. Start. Standard ASTM standard · ASTM C latest; Reinforced Plastic Piping Systems and Chemical Equipment; Plastic Building Products (ASTM VOL ) . C – 95 – This document is not an ASTM standard and is intended only to provide the user of an.

Author: Kajisho Shaktitaxe
Country: Seychelles
Language: English (Spanish)
Genre: Medical
Published (Last): 1 May 2009
Pages: 436
PDF File Size: 3.90 Mb
ePub File Size: 7.27 Mb
ISBN: 848-6-68036-389-9
Downloads: 80193
Price: Free* [*Free Regsitration Required]
Uploader: Zulkijas

This standard is issued under the fixed designation C ; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript epsilon e indicates an editorial change since the last revision or reapproval. This specification is limited to fabrication by contact molding. NOTE 1—The laminates covered by this specification are manufactured during fabrication of contact-molded RTP tanks, piping, and other equipment.

This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

The astn for reinforced thermoset plastic is RTP.

Astm c – astm normas fibra de vidrio

The resin matrix is applied by various methods, including brush, roller, or spray gun. Consolidation of the composite laminate is by rolling. Plastics and is the direct responsibility of Subcommittee D NOTE 5—Maximum flame spread designation by Test Method E 84 relates to measurement and description of the properties of materials, products, or systems in response to heat and flame under controlled laboratory conditions and should not be considered or used for the description or appraisal of the fire hazard of materials, products, or systems under actual fire conditions.

  LINDA NOCHLIN IMAGINARY ORIENT PDF

However, results of this test may be used as elements of a fire risk assessment that takes into account all the factors that are pertinent to an assessment of the fire hazard or a particular end use. B Calculated thickness for design purposes is determined as follows: D Corrosion barrier Plies 1, ashm, and 3 shall gel before structural plies are added. E Structural lay-up may be interrupted wstm intervals long enough to exotherm if required by the laminate manufacturing procedure and 6.

A Calculated thickness for design purposes is determined as follows: C Corrosion barrier Plies 1, 2, and 3 shall gel before structural plies are added. Location of exotherm plies may be shifted within the laminate body. No plies may be omitted. NOTE 6—The five Arabic grade numbers designate minimum physical property levels of a laminate obtained from tests of representative production process samples.

They are not arbitrarily selected values.

Astm c-582

See Table 1 and Table 2 for standard thicknesses. NOTE 7—Table 1 and Table 2 asrm for reference purposes and do not preclude other laminate-type constructions, such as nonwoven biaxial or unidirectional fabric, which may be agreed upon between the buyer and the seller, or may be added to this specification if they have been fully identified and characterized, as shown in Appendix X2.

Laminate designation from Table 3 shall consist of the abbreviation RTP followed by 1 type in Roman numerals; 2 class in capital letters followed by FS if required; 3 grade consisting of five Arabic numbers to designate xstm levels atm physical properties and 4 thickness designated by Arabic number in decimal inches or ALL, if properties apply to all thicknesses. Tensile strength, ultimate— psi 62 MPa. Tensile modulus—1 0 psi MPa. Flexural strength, ultimate—18 0 psi MPa.

Flexural modulus— 0 psi MPa. Tensile strength, ultimate—17 psi MPa. Flexural strength, ultimate—2 0 psi MPa. When such items are required, limits for each shall be agreed upon between the fabricator and the buyer.

A thixotropic agent may be added to the resin for viscosity control. NOTE 8—The addition of fillers, dyes, pigments, flame retardants, and thixotropic agents may interfere with visual inspection of laminate quality.

  IMUNOLOGIA CELULAR E MOLECULAR ABBAS PDF

Pastes shall be made with thixotropic agents. In combination with the cured resin, the surfacing veil helps determine the thickness of the resin-rich layer, reduces microcracking, and provides a nonwicking chemically resistant layer. Additional desirable considerations in choosing a veil for a specific application include: These products shall be a commercial grade of E-type glass fiber with a sizing that is compatible with the resin.

Next apply the specified surface mat, rolling so as to draw the resin through the mat for thorough wet-out and deaeration. As an alternative, a minimum of two passes of chopped roving minimum fiber length 1 in. Each pass of chopped roving or ply of chopped-strand mat shall be thoroughly rolled out.

This section of the laminate shall be allowed to exotherm prior to application of subsequent plies of reinforcement. Roll each ply for thorough wet-out and deaeration.

The final ply shall be mat or chopped roving equivalent. A surfacing mat is not required unless specified.

Surface resin may require the addition of paraffin or may be sealed with overlaid film, as required or approved by the resin producer, to ensure proper surface cure. Lapped edges of adjacent layers shall be staggered.

Gaps are not permitted. Astm c wilfredo row Enviado por: Parte 1 de 2 Standard Specification for Contact-Molded Reinforced Thermosetting Plastic RTP Laminates for Corrosion-Resistant Equipment1 This standard is issued under the c52 designation C ; the number immediately following the designation indicates the year of original adoption or, in the case of revision, c82 year of last revision.

Current edition approved Oct. Astm a Astm a ASTM Volume