74LS164N DATASHEET PDF

74LSN from Fairchild Semiconductor. Find the PDF Datasheet, Specifications and Distributor Information. 74LSN Datasheet, 74LSN PDF, 74LSN Data sheet, 74LSN manual, 74LSN pdf, 74LSN, datenblatt, Electronics 74LSN, alldatasheet. These 8-bit shift registers feature gated serial inputs and an asynchronous clear. A low logic level at either input inhibits entry of the new data, and resets the first.

Author: Shajinn Nejora
Country: Mali
Language: English (Spanish)
Genre: Travel
Published (Last): 9 September 2004
Pages: 111
PDF File Size: 20.92 Mb
ePub File Size: 3.20 Mb
ISBN: 631-5-14979-213-4
Downloads: 90025
Price: Free* [*Free Regsitration Required]
Uploader: Fek

By using our site, you acknowledge 74l1s64n you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service. When I power-on daasheet circuit, all the LEDs are off. Then I send a clock pulse from the Raspberry Pi go high for ms then go low. I took some photos of the scope, the first is the clock from the GPIO without nothing and the second is the clock connected to the register.

I resolved my problem.

The register was clocking multiple times because the clock signal wasn’t enough clean. So I added a schmitt trigger between the raspberry pi and the register clock input, and now it shifts exactly the number I want. A Low power Schottky input typically sits at about 1. Cleaning the pulse up with a Schmitt trigger got it working, but is masking the real problem – you Pi’s 74lss164n line is either not being controlled correctly by your program, or it’s blown up.

Take a peek at the data sheet. This chip can’t drive the kind of daatsheet you want it to. Thus exceeding operating conditions, all bets are off.

You likely have reflections on your clock line, causing it to be treated as multiple clock pulses. The length of your clock wire might be a factor in this.

  KONVENSI PARIS 1919 PDF

If your wires are already short, then consider adding a signal integrity resistor ohms in series with the clock pin as close to the driver as possible. By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

Home Questions Tags Users Unanswered. What am I doing wrong? James Magnus 55 7. Do you have an oscilloscope? You are probably getting multiple pulses instead of just one.

Or, the pulse has a ragged edge s and the is actually clocking several times. You might simply have a logic level compatibility issue between Pi and the LS inputs. Might datasueet missing decoupling capacitors too. FiddyOhm Reading the datasheet here, I can’t find an issue with the logic levels.

The thresholds are 0.

See this answer to a previous topic, for more info. You have an unexplained 1V offset. Perhaps this has something to do with your problem.

How Would You Build Moving LED Signs Using IC 74LS164? Pin-Outs Explored

Finding out where that offset comes from should be the absolute first priority here. Thanks for all your advices and suggestions, have a ddatasheet day.

I know there is a pull down and a pull up in the raspberry pi when you configure the GPIO as input, but is there a pull down when you are in output mode? Output mode is datashset with at least 2mA sink capability. I use leds to see what happen.

74LSN datasheet, 74LSN datasheets, manuals for 74LSN electornic semiconductor part

In real I will put mosfets to control a big led board. Negative seems to indicate source current, and positive sink current.

  JURNAL JENAYAH RAGUT PDF

You should test with the FETs in place. You might even need to replace the shift register, datxsheet probably not. Better yet, JamesMagnus, you have a scope.

Just disconnect the LEDs and use the scope to check outputs. That’s a good guess, but the recent oscilloscope pictures posted after your answer looks pretty clean.

That’s pretty far fetched, given the frequencies involved. Looks pretty clean but you need to zoom way in to know for sure. Also, why does the scope only show 2Vpp in one picture? The measurement or what I think is the measurement number in all the screen shots says 3.

Have you ever had bounce problems using a simple microcontroller DIO, especially at low freq? Hasn’t ever happened to me. When the asker is sourcing more than the chip can do by more than a factor of 10, I’d look there first. Sign up or log in Sign up using Google.

Sign up using Facebook. Sign up using Email and Password. Post as a guest Name. Email Required, but never shown. Post Your Answer Discard By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.